99国精免费看,夜夜骑免费视频,日韩一区二区三区小视频,精品久久久久国产观看

歡迎進入濟南濟柴環能燃?xì)獍l(fā)電設備有限公司官網！
當前位置：首頁 - 新聞中心 - 公司新聞

公司新聞

沼氣發電機組熄火后有時會有什么狀況出現？

返回 2022.08.25 來源：http://www.51credits.cn 0
有時沼氣發電機組熄火后，馬上啟動會出現啟動困難，這時要檢查一下沼氣發電機組的工作情況，看配氣系統、點火系統是否有故障，然后檢查下面幾項：
Sometimes it is difficult to start the biogas generator set immediately after the flameout. At this time, check the working condition of the biogas generator set to see if there is any fault in the gas distribution system and ignition system, and then check the following items:
1)電磁閥過熱，閥芯卡滯或磁力下降。
1) The solenoid valve is overheated, the valve element is stuck or the magnetic force drops.
2)電控插頭是否有接觸不良。
2) Check whether the electric control plug has poor contact.
3)混合器閥芯是否有卡滯現象，使混合氣過濃、過稀。
3) Check whether the valve element of the mixer is stuck, so that the mixture is too rich and too thin.
4)減壓器輸出壓力是否過高，超出正常值。
4) Whether the output pressure of the pressure reducer is too high, exceeding the normal value.
5)檢查受溫度影響的部件。
5) Check components affected by temperature.
5.電磁閥打不開
5. Solenoid valve cannot be opened
減壓器電磁閥打不開的原因可能是以下幾點：
The reason why the solenoid valve of the pressure reducer cannot be opened may be the following:
1)電源未接通或電磁閥搭鐵不好，也可能是電壓過低，啟動時壓降過大，啟動時檢查電瓶電壓，電源變換器輸出電壓是否有12V。
1) The power supply is not connected or the grounding of the solenoid valve is not good, or the voltage may be too low and the voltage drop is too large during startup. Check the battery voltage and whether the output voltage of the power converter is 12V during startup.
沼氣發電機組
2)磁線圈故障，開啟功率不足。
2) Magnetic coil fault, insufficient opening power.
3)閥芯通氣孔被堵。
3) The vent hole of the valve element is blocked.
4)ECU無輸出控制信號。
4) ECU has no output control signal.
5)閥芯和鐵心的配合間隙太小，閥芯不能自由滑動。
5) The fitting clearance between the valve core and the iron core is too small, and the valve core cannot slide freely.
6)閥芯O形圈或橡膠墊損壞。
6) The O-ring or rubber gasket of the valve element is damaged.
沼氣發電機組熄火后有時會有什么狀況出現？熱車不易啟動，要知道原因和檢查事項就來看看內容吧，更多內容就來我們網站http://www.51credits.cn咨詢了解！
What happens sometimes after the biogas generator unit shuts down? The hot car is not easy to start. If you want to know the reasons and inspection items, please check the contents. For more information, please visit our website http://www.51credits.cn Consult and understand!

上一條：焦化發電機組曲軸主軸承響怎么診斷

下一條：瓦斯發電機組進行小修的目的和內容

新聞搜索
濟南濟柴環能燃?xì)獍l(fā)電設備有限公司

  • 服務熱線

    0531-62325028
    0531-69951266
首頁 - 新聞中心 > 公司新聞

沼氣發電機組熄火后有時會有什么狀況出現？

有時沼氣發電機組熄火后，馬上啟動會出現啟動困難，這時要檢查一下沼氣發電機組的工作情況，看配氣系統、點火系統是否有故障，然后檢查下面幾項：
Sometimes it is difficult to start the biogas generator set immediately after the flameout. At this time, check the working condition of the biogas generator set to see if there is any fault in the gas distribution system and ignition system, and then check the following items:
1)電磁閥過熱，閥芯卡滯或磁力下降。
1) The solenoid valve is overheated, the valve element is stuck or the magnetic force drops.
2)電控插頭是否有接觸不良。
2) Check whether the electric control plug has poor contact.
3)混合器閥芯是否有卡滯現象，使混合氣過濃、過稀。
3) Check whether the valve element of the mixer is stuck, so that the mixture is too rich and too thin.
4)減壓器輸出壓力是否過高，超出正常值。
4) Whether the output pressure of the pressure reducer is too high, exceeding the normal value.
5)檢查受溫度影響的部件。
5) Check components affected by temperature.
5.電磁閥打不開
5. Solenoid valve cannot be opened
減壓器電磁閥打不開的原因可能是以下幾點：
The reason why the solenoid valve of the pressure reducer cannot be opened may be the following:
1)電源未接通或電磁閥搭鐵不好，也可能是電壓過低，啟動時壓降過大，啟動時檢查電瓶電壓，電源變換器輸出電壓是否有12V。
1) The power supply is not connected or the grounding of the solenoid valve is not good, or the voltage may be too low and the voltage drop is too large during startup. Check the battery voltage and whether the output voltage of the power converter is 12V during startup.
沼氣發電機組
2)磁線圈故障，開啟功率不足。
2) Magnetic coil fault, insufficient opening power.
3)閥芯通氣孔被堵。
3) The vent hole of the valve element is blocked.
4)ECU無輸出控制信號。
4) ECU has no output control signal.
5)閥芯和鐵心的配合間隙太小，閥芯不能自由滑動。
5) The fitting clearance between the valve core and the iron core is too small, and the valve core cannot slide freely.
6)閥芯O形圈或橡膠墊損壞。
6) The O-ring or rubber gasket of the valve element is damaged.
沼氣發電機組熄火后有時會有什么狀況出現？熱車不易啟動，要知道原因和檢查事項就來看看內容吧，更多內容就來我們網站http://www.51credits.cn咨詢了解！
What happens sometimes after the biogas generator unit shuts down? The hot car is not easy to start. If you want to know the reasons and inspection items, please check the contents. For more information, please visit our website http://www.51credits.cn Consult and understand!