在線咨詢
官方二維碼
當前位置：
2022.07.08
焦化發電機組安裝、使用、維護步驟是怎樣的？
焦化發電機組安裝、使用、維護，應按照以下步驟一次進行。具體內容小編來講解一番吧。
The installation, use and maintenance of coking generator set should be carried out at one time according to the following steps. Let's explain the specific content.
認真閱讀隨機使用、維護說明書
Carefully read the random use and maintenance instructions
開箱后，找到隨機的使用、維護說明書，認真、仔細閱讀相關內容，并按照說明書要求辦理。發電機組的安裝、使用、維護，應按照以下步驟一次進行：
After unpacking, find the accompanying operation and maintenance instructions, carefully read the relevant contents, and handle according to the requirements of the instructions. The installation, use and maintenance of the generator set should be carried out at one time according to the following steps:
1、嚴格按照說明書要求辦理；
1. Strictly follow the instructions;
2、具體事宜，參照安裝說明指引辦理。
2. Refer to the installation instructions for specific matters.
焦化發電機組安裝過程中幾點注意到事項
Several notices in the installation of coking generator set
1、進口處應以軟管連接（按照預留接口，接入沼氣管路）。
1. The biogas inlet shall be connected with a hose (connect the biogas pipeline according to the reserved interface).
2、發動機尾氣出口處應注意螺紋管是否安裝就緒，螺紋管可減小機組運行時對排氣管道的震動（按照預留法蘭，連接排氣管至機房外）。
2. Pay attention to whether the threaded pipe is installed well at the exhaust outlet of the engine. The threaded pipe can reduce the vibration of the exhaust pipe during the operation of the unit (connect the exhaust pipe to the outside of the machine room according to the reserved flange).
3、潤滑油（打開機油口蓋，加入機油至要求數量）；當環境溫度高于–15℃時推薦15W/40級潤滑油，當環境溫度低于–15℃時推薦使用5W/30。能使用燃氣發動機專用潤滑油能為燃氣發動機提供良好的潤滑作用。
3. Lubricating oil (open the oil cap and add oil to the required quantity); 15w/40 grade lubricating oil is recommended when the ambient temperature is higher than – 15 ℃, and 5w/30 grade lubricating oil is recommended when the ambient temperature is lower than – 15 ℃. Being able to use special lubricating oil for gas engine can provide good lubrication for gas engine.
4、機油尺（拔出機油尺，檢查機油液面，保證機油在適當位置）。
4. Oil dipstick (pull out the oil dipstick and check the oil level to ensure that the oil is in the proper position).
5、內循環冷卻水加注（依據當?shù)貧鉁貭顩r，加注適當防凍液）。
5. Fill with internal circulating cooling water (fill with appropriate antifreeze according to the local temperature).
6、安裝輸出電纜處（打開蓋板，連接電力輸出電纜，建議：依據不同功率機組的輸出電流選用適合的四芯銅質電纜）。
6. Install the output cable (open the cover plate and connect the power output cable. It is recommended to select the appropriate four core copper cable according to the output current of different power units).
以上就是問題解答的相關內容了，希望能夠幫助到大家，如對這一問題還存在任何疑問，都歡迎關注我們網站http://www.51credits.cn并咨詢我們的工作人員，將竭誠為您服務。
The above is the relevant content of the question answer. I hope it can help you. If you still have any questions about this problem, you are welcome to follow our website http://www.51credits.cn And consult our staff, will serve you wholeheartedly.