99国精免费看,夜夜骑免费视频,日韩一区二区三区小视频,精品久久久久国产观看

歡迎進入濟南濟柴環能燃?xì)獍l(fā)電設備有限公司官網!

常見問題解答

焦化發電機組啟動前后的檢查以及停機操作

返回 2022.07.15 來源:http://www.51credits.cn 0
不管是使用什么家電、開什么車或者是使用某一種工具的時候,我們都說要安全使用。對于焦化發電機組也是一樣,想要安全操作使用發電機組需要注意三大事項。
No matter what household appliances we use, what cars we drive or what tools we use, we all say we should use them safely. The same is true for the coking generator set. If you want to operate the generator set safely, you need to pay attention to three matters.
啟動前檢查
Pre startup inspection
1、檢查焦化發電機組機油油位是否在標示刻度線以?xún)?nèi),不夠加同型號機油至標示線以?xún)?nèi)。
1. Check whether the oil level of the coking generator set is within the marked mark, and if it is not enough, add oil of the same model to the mark.
2、檢查冷卻液是否在水箱蓋以下6mm左右,不夠加清水至上述位置。
2. Check whether the coolant is about 6mm below the water tank cover, and add water to the above position if not enough.
3、檢查電解液液位是否在極板面上15mm左右,不夠加蒸餾水至上述位置。
3. Check whether the electrolyte level is about 15mm above the plate surface, and add distilled water to the above position if not enough.
4、檢查發電機周?chē)延械K操作或運行的物品搬開,使得通風通暢。
4. Check the surroundings of the generator and remove the objects that hinder the operation or operation to make the ventilation unobstructed.
5、使得焦化發電機組總開關在OFF(關)狀態。
5. Make the main switch of coking generator set in off state.
6、使得燃油箱油量在一半以上,燃油供油閥常開。
6. Make the fuel volume in the fuel tank more than half, and the fuel supply valve is normally open.
焦化發電機組
啟動中
Starting
1、使得控制屏上各按鈕已經復位,將速度操作手柄調到怠速位置
1. Make all buttons on the control screen have been reset, and adjust the speed operating handle to the idle position
2、把鑰匙轉到開的位置,按下啟動按鈕焦化發電機啟動。
2. Turn the key to the on position and press the start button to start the coking generator.
3、將速度調節手柄慢慢上調直至電壓為400V;頻率、50赫芝時擰緊固定手柄螺母,發電機正常運行。
3. Slowly raise the speed adjusting handle until the voltage is 400V; Tighten the fixed handle nut when the frequency is 50 Hz, and the generator operates normally.
4、焦化發電機正常情況下,一次啟動著車或三次啟動著車,如果焦化發電機組三次不能啟動著車,控制面板上的故障指示燈亮,此時應查明原因并排除故障再啟動。
4. Under normal conditions, the coking generator starts and stops at one time or three times. If the coking generator unit cannot start and stops at three times, the fault indicator light on the control panel is on. At this time, find out the cause and eliminate the fault before starting.
5、啟動著車后應檢查有無噪音或震動,有無漏油,有無漏水,漏氣現象,控制屏有無異常顯示,在開機10~15秒內油壓應達到正常范圍((35~60p.s.i)如有不正常情況應做出相應的整改,待正常后合上發電機總開關開始供電。
5. After starting the vehicle, check whether there is noise or vibration, whether there is oil leakage, whether there is water leakage, air leakage, and whether the control panel has abnormal display. The oil pressure should reach the normal range ((35~60p.s.i) within 10~15 seconds of starting the machine. If there is any abnormal condition, make corresponding rectification, and turn on the main switch of the generator to start power supply after it is normal.
停機
Shutdown
1、先扳下發電機總開關,讓發電機空載運行5分鐘,然后把調速手柄扳到怠速位置運行5分鐘再扳到STOP的位置,焦化發電機停機。
1. First pull down the main switch of the generator and let the generator run without load for 5 minutes, then turn the speed control handle to the idle position for 5 minutes, and then turn it to the stop position, and the coking generator stops.
2、如有緊急情況需停車,可以不扳下發電機總開關直接將調速手柄扳到的位置焦化發電機停機。
2. If there is an emergency that requires shutdown, the coking generator can be shut down by directly turning the speed control handle to the position without pulling down the main switch of the generator.
以上就是今天為大家介紹的關于問題以及注意事項的全部?jī)?nèi)容,希望對大家能有所幫助,想要了解更多內容可以電話聯系我們或者關注我們的網站http://www.51credits.cn,我們的工作人員會及時與您取得聯系。
The above is all about the problems and precautions introduced to you today. I hope it can help you. If you want to know more, you can contact us by phone or follow our website http://www.51credits.cn , our staff will contact you in time.
新聞搜索
濟南濟柴環能燃?xì)獍l(fā)電設備有限公司
  • 服務熱線

    0531-62325028
    0531-69951266

焦化發電機組啟動前后的檢查以及停機操作

不管是使用什么家電、開什么車或者是使用某一種工具的時候,我們都說要安全使用。對于焦化發電機組也是一樣,想要安全操作使用發電機組需要注意三大事項。
No matter what household appliances we use, what cars we drive or what tools we use, we all say we should use them safely. The same is true for the coking generator set. If you want to operate the generator set safely, you need to pay attention to three matters.
啟動前檢查
Pre startup inspection
1、檢查焦化發電機組機油油位是否在標示刻度線以?xún)?nèi),不夠加同型號機油至標示線以?xún)?nèi)。
1. Check whether the oil level of the coking generator set is within the marked mark, and if it is not enough, add oil of the same model to the mark.
2、檢查冷卻液是否在水箱蓋以下6mm左右,不夠加清水至上述位置。
2. Check whether the coolant is about 6mm below the water tank cover, and add water to the above position if not enough.
3、檢查電解液液位是否在極板面上15mm左右,不夠加蒸餾水至上述位置。
3. Check whether the electrolyte level is about 15mm above the plate surface, and add distilled water to the above position if not enough.
4、檢查發電機周?chē)延械K操作或運行的物品搬開,使得通風通暢。
4. Check the surroundings of the generator and remove the objects that hinder the operation or operation to make the ventilation unobstructed.
5、使得焦化發電機組總開關在OFF(關)狀態。
5. Make the main switch of coking generator set in off state.
6、使得燃油箱油量在一半以上,燃油供油閥常開。
6. Make the fuel volume in the fuel tank more than half, and the fuel supply valve is normally open.
焦化發電機組
啟動中
Starting
1、使得控制屏上各按鈕已經復位,將速度操作手柄調到怠速位置
1. Make all buttons on the control screen have been reset, and adjust the speed operating handle to the idle position
2、把鑰匙轉到開的位置,按下啟動按鈕焦化發電機啟動。
2. Turn the key to the on position and press the start button to start the coking generator.
3、將速度調節手柄慢慢上調直至電壓為400V;頻率、50赫芝時擰緊固定手柄螺母,發電機正常運行。
3. Slowly raise the speed adjusting handle until the voltage is 400V; Tighten the fixed handle nut when the frequency is 50 Hz, and the generator operates normally.
4、焦化發電機正常情況下,一次啟動著車或三次啟動著車,如果焦化發電機組三次不能啟動著車,控制面板上的故障指示燈亮,此時應查明原因并排除故障再啟動。
4. Under normal conditions, the coking generator starts and stops at one time or three times. If the coking generator unit cannot start and stops at three times, the fault indicator light on the control panel is on. At this time, find out the cause and eliminate the fault before starting.
5、啟動著車后應檢查有無噪音或震動,有無漏油,有無漏水,漏氣現象,控制屏有無異常顯示,在開機10~15秒內油壓應達到正常范圍((35~60p.s.i)如有不正常情況應做出相應的整改,待正常后合上發電機總開關開始供電。
5. After starting the vehicle, check whether there is noise or vibration, whether there is oil leakage, whether there is water leakage, air leakage, and whether the control panel has abnormal display. The oil pressure should reach the normal range ((35~60p.s.i) within 10~15 seconds of starting the machine. If there is any abnormal condition, make corresponding rectification, and turn on the main switch of the generator to start power supply after it is normal.
停機
Shutdown
1、先扳下發電機總開關,讓發電機空載運行5分鐘,然后把調速手柄扳到怠速位置運行5分鐘再扳到STOP的位置,焦化發電機停機。
1. First pull down the main switch of the generator and let the generator run without load for 5 minutes, then turn the speed control handle to the idle position for 5 minutes, and then turn it to the stop position, and the coking generator stops.
2、如有緊急情況需停車,可以不扳下發電機總開關直接將調速手柄扳到的位置焦化發電機停機。
2. If there is an emergency that requires shutdown, the coking generator can be shut down by directly turning the speed control handle to the position without pulling down the main switch of the generator.
以上就是今天為大家介紹的關于問題以及注意事項的全部?jī)?nèi)容,希望對大家能有所幫助,想要了解更多內容可以電話聯系我們或者關注我們的網站http://www.51credits.cn,我們的工作人員會及時與您取得聯系。
The above is all about the problems and precautions introduced to you today. I hope it can help you. If you want to know more, you can contact us by phone or follow our website http://www.51credits.cn , our staff will contact you in time.